Cast Turn Signal Flat Side STD
兩個一組共同販售,附外六角短螺絲(M8 x 20mm) 兩個。 可另外加購鑽孔處理螺絲:M8 x 35mm 內六角螺絲 100 元 / 個M8 x 20mm 外六角螺絲 70 元 / 個   FORK original cast turn signal"Flat Side"has cutaway shapes on both side.  
NT$ 5,700
Add to Wish List
Narrow Rise clamp Flat - Shoulder
此冠座比原本再窄 50mm 寬,適合搭配 Fork 的窄手把以實現更為窄身的比例,並通過一體式的基座來提高剛性! 上夾具寬度僅 80mm,中心高度也是只有 80mm,其窄體也更能集中轉向力。 - The top clamp width are 50mm narrower than genuine.This clamp make it possible to have super narrow shape of handlebar out line.The one piece base clamp gains more stiffness against the...
NT$ 10,200
Add to Wish List
Narrow rise bar ”Medium Rise”
為 Fork 窄冠座專門設計的手把,中間寬度僅為 80mm,所以無法適用一般冠座,購買前請務必留意! - The spacial handlebar for narrow rise clamp. The straight section for clamping is only 80mm. Width: 640mmHight: 145mmPull back: 175mm made of stainless steel
NT$ 4,900
Add to Wish List
Narrow rise bar ”Low Rise”
為 Fork 窄冠座專門設計的手把,中間寬度僅為 80mm,所以無法適用一般冠座,購買前請留意! - The spacial handlebar for narrow rise clamp. The straight section for clamping is only 80mm. Width:640mmHight: 80mmPull back:140mm made of stainless steel
NT$ 4,900
Add to Wish List
Narrow rise bar ”Super Mini Robot”
為 Fork 窄冠座專門設計的手把,中間寬度僅為 80mm,所以無法適用一般冠座,購買前請留意! - The spacial handlebar for narrow rise clamp. The straight section for clamping is only 80mm. Width:500mmHight: 50mmPull back:50mm made of stainless steel
NT$ 7,000
Add to Wish List
Narrow rise bar ”British high”
為 Fork 窄冠座專門設計的高把,中間寬度僅為 80mm,所以無法適用一般冠座,購買前請留意! - The spacial handlebar for narrow rise clamp. The straight section for clamping is only 80mm. Width:700mmHight: 225mmPull back:150mm made of stainless steel
NT$ 5,200
Add to Wish List
Shark Fin Visor - Polished
Narrow glide 經典窄身的大燈頭罩,以優美的曲線及恰到好處的比例呈現的“鯊魚鰭”式樣,可以 800 元加購內版,將一些小型的儀表指示燈藏在內側以求更為乾淨簡潔的外觀! 隨附兩顆螺栓與墊圈,內版則為不鏽鋼製成,隨附四顆螺絲。   - Shark Fin Visor is the head light visor for narrow glide top bridge with 39 or 35mm front fork. The genuine visor is the one of the icon parts in the narrow...
from NT$ 7,100
Add to Wish List
6112 Oil filter cover for SR400 / SR500 - Radial Fin
SR400 & SR500 適用的鋁鑄機油濾清器蓋 以鰭型放射狀設計帶來獨特的復古感 雖然是小配件,但卻是手工車不可或缺的美觀細節! 厚度 27mm *附 O-ring 與不鏽鋼洩氣螺絲、銅墊圈
NT$ 3,600
Add to Wish List
HZT115 Series Carb Cover - Arrow
Fork 熱門的原創化油器蓋設計,小巧的身形但也保證進氣量的充足。 可單售,亦可搭配 S&S B 或 Linkert 兩種底座組合販售,隨附不鏽鋼螺栓,有底座的朋友也可以單購外殼。 *無濾芯設計   - It is very small carb cover but has good air flow It consists of base and shell. Air filter is NOT equipped. S&S B base also could mount on Keihin butterfly...
from NT$ 7,400
Add to Wish List
7137 Carburetor Top Cover for W650 - Rounded Fin
W650專用鋁鑄化油器上蓋(不適用 W800 & W400) 圓頂鰭片造型與汽缸機頂蓋相似,具有相當協調性的美觀作品! 同時也有傳感器蓋與齒輪蓋可另外加購,讓整體外觀更完整! (齒輪蓋也適合W800和400。)  價格為一組兩個成對販售,並附有不銹鋼專用螺栓。   - These are cast aluminum carburetor diaphragm cover for W650. They match up so well with the motor and also add spice to appearance of whole bike. "Rounded Fin" has similar...
NT$ 4,700
Add to Wish List
7101 Kawasaki W Bevel Gear Cover BLACK
Fork 經典原創作品之一 識別性的 W 字樣,來自 Kawasaki W1SA 及 W3 的 Y 字側蓋上的設計, 雙邊鰭片與引擎上的散熱鰭片又有著無與倫比的協調性! 帶有濃厚的復古味與鋁鑄質感, 是 W400/W650/W800 提升細節的重要配件!   - The classic logo and line on "Y" cover of W1SA and W3 are on the bevel gear cover of new W. Fins...
NT$ 4,900
Add to Wish List
1173 Derby Cover for Sportster - 7 FIN BLACK
適用 2004 年以後 Sportster 的六孔離合器邊蓋 鰭片高度約 12mm 左右   *此產品不包含螺絲,請使用原裝螺絲安裝   Here is Derby Cover for rubber mount Sportster 2004-. Maximum Fin height is almost half inch. Top of fins are hairline finished. Bolts are not included, please use genuine....
NT$ 5,100
Add to Wish List
1173 Derby Cover for Sportster - 7 FIN
適用 2004 年以後 Sportster 的六孔離合器邊蓋 鰭片高度約 12mm 左右   *此產品不包含螺絲,請使用原裝螺絲安裝   Here is Derby Cover for rubber mount Sportster 2004-. The pitch of fins are almost same as motor's fin. Top of fins are polished. Bolts are not included, please...
NT$ 4,700
Add to Wish List
1103 Sportster point cover - 5 FIN
此款正時蓋可直上 70 - 2003 Sportster 現今哈雷 883、48 只要旋轉 90 度同樣通用 Ignition timing cover for Sportster. Thickness 20.5mm.Fin hight 9mm.Stainless steel bolts are included. Note) There is a thick, may interfere with the brake pedal and foot controls. Please make sure the...
NT$ 3,000
Add to Wish List
1135 series Tear Drop Carb Cover - BLACK FIN
Fork 原創淚滴型設計 小巧的造型使雨水難以進入 但也保證進氣量的充足 此款可直上 S&S E CV/EFI/SU 可另外加購轉接座 無濾芯設計   Carb cover for S&S Soper E(or G).About 6" in width (horizontal direction). 1-3/4" in thick. For S&S E,You colud use Velocity lip(1135-03) to have more air flow.For Keihin CV...
NT$ 7,400
Add to Wish List
1101 Sportster point cover - 7 FIN BLACK
此款正時蓋可直上 1970-1999 Big Twin 引擎 以及 2004 至今的 Sportster 而 03 年以前的 Sportster 只要旋轉 90 度同樣通用 The fin pitch and thickness are similar to cylinder fin. Thickness 21mm, fin height 12.5mm. stainless steel bolts are included. Note) There is a...
NT$ 3,300
Add to Wish List
Narrow Rise clamp Flat - Type"H"
此冠座比原本再窄 50mm 寬,適合搭配 Fork 的窄手把以實現更為窄身的比例,並通過一體式的基座來提高剛性! 上夾具寬度僅 80mm,中心高度也是只有 80mm,其窄體也更能集中轉向力。 - The top clamp width are 50mm narrower than genuine. This clamp make it possible to have super narrow shape of handlebar out line.The one piece base clamp gains more stiffness against the...
NT$ 9,500
Add to Wish List
Narrow rise bar ”British high WIDE”
為 Fork 窄冠座專門設計的手把,中間寬度僅為 80mm,所以無法適用一般冠座,購買前請留意! - The spacial handlebar for narrow rise clamp. The straight section for clamping is only 80mm. Width:855mmHight: 235mmPull back:180mm made of stainless steel
NT$ 5,200
Add to Wish List
6112 Oil filter cover for SR400 / SR500 - LUXE
由 LUXE Motorcycle 設計 大小不一的圓形仿若與 SR 圓型機殼對應 底部刻劃的橫線也與發動機鰭片有著整體一致的協調感 尤其手工鋁鑄的復古質感,雖然是小配件 但卻是手工車不可或缺的美觀細節!   厚度 19mm *附 O-ring 與不鏽鋼洩氣螺絲、銅墊圈
NT$ 3,600
Add to Wish List
6112 Oil filter cover for SR400 / SR500 - EMBOSS
SR400 & SR500 適用的鋁鑄機油濾清器蓋 中心略帶凹痕的圓形主體加上浮雕字母帶來獨特的復古感 雖然是小配件,但卻是手工車不可或缺的美觀細節 厚度 20mm *附 O-ring 與不鏽鋼洩氣螺絲、銅墊圈
NT$ 3,600
Add to Wish List
HZT115 Series Carb Cover - Plain
Fork 熱門的原創化油器蓋設計,小巧的身形但也保證進氣量的充足。 搭配 S&S B 或 Linkert 兩種底座組合販售,隨附不鏽鋼螺栓,有底座的朋友也可以單購外殼。 *無濾芯設計   - It is very small carb cover but has good air flow It consists of base and shell. Air filter is NOT equipped. S&S B base also could mount on Keihin butterfly...
from NT$ 7,000
Add to Wish List
HZT115 Series Carb Cover - Fin
Fork 熱門的原創化油器蓋設計,小巧的身形但也保證進氣量的充足。 有搭配 S&S B 或 Linkert 兩種底座組合販售,隨附不鏽鋼螺栓,有底座的朋友也可以單購外殼。 *無濾芯設計   - It is very small carb cover but has good air flow It consists of base and shell. Air filter is NOT equipped. S&S B base also could mount on Keihin butterfly...
from NT$ 7,400
Add to Wish List
7137 Throttle Sensor Cover for W650 / W400
W650 & W400 專用鋁鑄節氣門傳感器蓋(不適用 W800),可替換醜陋的原裝黑色塑料蓋,同時也有化油器上蓋與齒輪蓋可加購,讓整體外觀更完整!(齒輪蓋也適合W800和400。) 附有專用不銹鋼螺栓 - It is a cast aluminum throttle position sensor cover for W650. If you don't like plastic sensor on the right side of carburetor, we recommend to use this.Especially if you buy our Carburetor...
NT$ 1,800
Add to Wish List
7137 Carburetor Top Cover for W650 - Sharp Fin
W650 專用鋁鑄化油器上蓋(不適用 W800 & W400) 圓頂造型與汽缸機頂蓋相似,具有相當協調性的美觀作品! 價格為一組兩個,並附有不銹鋼螺栓。同時也有傳感器蓋與齒輪蓋可加購,讓整體外觀更完整! (齒輪蓋也適合W800和400。)   - These are cast aluminum carburetor diaphragm cover for W650.They match up so well with the motor and also add spice to appearance of whole bike. "Sharp Fin" has similar fins...
NT$ 4,700
Add to Wish List
You have successfully subscribed!
This email has been registered
ico-collapse
0
ic-cross-line-top
ic-expand
ic-cross-line-top